Guide · For installers
Reading a PPF data sheet: what each row means
A PPF data sheet describes the film layer by layer: its thickness, the base material, the top coat, the temperature at which the top coat heals, how strongly it beads water, how glossy it is and how far it stretches before it breaks. Read each figure with one question: is it measured on this film, or typical of the class?
Thickness
Quoted in mils, thousandths of an inch. Ask which layers the figure counts: film alone, film and adhesive, or the liner too. Defender: 8.5 mil. Is thicker film better?
Base material: aliphatic or aromatic TPU
The base is the bulk of the film, usually a thermoplastic polyurethane (TPU). The word in front of it names the kind of urethane: aliphatic or aromatic. The two behave differently in sunlight, and a sheet that names one is telling you which chemistry the film is built on. ARK’s base row reads Aliphatic TPU. Thickness and warranty are ARK’s own figures. The other rows are industry-typical values for this class of film, confirmed by ARK for publication, not ARK test results.
How a particular film holds up in sun is a matter of its whole construction, the adhesive and the top coat included, and of measurement over time. ARK publishes no yellowing result yet.
Top coat
The thin outer layer that carries the surface: gloss or satin, water repellency, stain resistance and self-healing. Fusion’s row reads Ceramic-infused hydrophobic self-healing coat.
Self-heal activation
The temperature the data sheet gives for the top coat to relax back over a light mark. Light marks close faster the warmer the surface, and more slowly in the cold, which is why sun or a warm rinse helps. The row on ARK’s sheets: 60 °C. It says nothing about deep marks: if you can catch it with a fingernail, it stays.
Water contact angle
The angle a water droplet makes where it meets the surface. The higher the angle, the rounder the bead and the more readily water rolls off; above 90° a surface is usually called hydrophobic. Fusion, the ceramic gloss film: 105 °. The effect fades with use and comes back with maintenance.
Gloss at 60°
Measured with a gloss meter at a 60° angle, in gloss units (GU). Higher is shinier; a satin film reads far lower on purpose. Defender: 92 GU. Umbra (a working name), the satin film: 20 GU.
Elongation at break
How far a sample stretches, as a share of its length, before it breaks. It shows how much the film tolerates on curves, but fitting never goes near that limit: film stretched far enough to whiten is already a stretch mark. Defender: 350%.
The roll label
The label is the part of the sheet that travels with the film. It should print the film, thickness, finish, warranty, roll size and a lot number. ARK’s standard roll is 60 in × 50 ft. Write the lot on every job record, because a roll traces back to its batch when a claim comes in.
The honest limit
A data sheet is only as good as its sources
A figure without a test behind it is a claim. Ask which rows are measured on the film itself. ARK says so beside every sheet: Thickness and warranty are ARK’s own figures. The other rows are industry-typical values for this class of film, confirmed by ARK for publication, not ARK test results.
Where to go from here.
The films
- DefenderGloss. The thick clear film, for the driver asking how much stone a hood can take before it chips.Explore Defender
- FusionCeramic gloss. Clear gloss film with the water-repellent layer in its own top coat, for the buyer weighing film plus a separate coating.Explore Fusion
- UmbraSatin. Satin film for two buyers: the one who wants gloss paint turned satin, and the one whose factory matte paint cannot be colour-matched or polished.Explore Umbra
- SpectrumColour. Colour film for the buyer choosing between a vinyl wrap and a change of colour that also protects the paint. It is not the answer to a clear-film question.Explore Spectrum
- Apply to carry ARKTell ARK the work your shop does, and a person replies about rolls, kits and becoming an authorized dealer.Apply to carry ARK

Carry ARK in your shop.
info@arkppf.comA person reads it, and answers within one business day.